How To Wire A UK Plug (3 Wire and 2 Wire): Step By Step Guide (2024)

In the UK, plugs come in either 3-wire or 2-wire varieties. The type you need depends on the equipment you’re using and where it’s being plugged in. In this guide, we’ll show you how to wire both types of plug, step by step. We’ll also explain when each type is used. Read on to learn more!

Plugs are used all around us on electrical equipment and appliances that require electrical energy to operate. Plugs are generally easy to wire and only require a few basic tools. An incorrectly wired plug can cause all sorts of issues on an electrical piece of equipment.

In this guide, we will show you the step-by-step process of how to wire a plug using a 3 core cable (live, neutral, and earth). If you do not feel competent to carry out any electrical work then you should always consult an electrician or someone who is electrically competent.

What you will need

There are a number of tools that you will require when wiring a plug. We have listed some of the tools that we recommend to use when wiring a plug. We have listed some of our favourite tools that we use in industry and that would be suitable for wiring a plug. Please note, that we may make a small commission if you purchase any tools using our links.

Terminal screwdriver

Side cutters

Stanley knife

Preparing the cable

One of the first things that you should do is to prepare the cable.

First, you should visually inspect the cable checking for any damage or defects. Check that all insulation is intact and that the cores of each cable are not touching.

If you are using a new cable you will need to remove some of the plastic insulation (normally around 4cm). The best way to do this is by carefully using a sharp knife or a pair of side cutters. If you are using an existing cable just ensure that the insulation on each core is in good condition.

Next, you will need to cut the wires to length. Separate each core from the other and cut to the desired length. A plug is designed to disconnect the live first in the event of a cable being pulled out. Do not leave all of the cores the same length as this will cause you issues when you are trying to close up the plug. The earth wire should be the longest, followed by the neutral then the live should be the shortest.

The next step is to remove some of the insulation from each core so they can be terminated. You should move approximately 4 – 5mm of plastic insulation off each core. The best way to do this is using a set of wire strippers. Side cutters can also be used but extra care must be taken to avoid damaging any of the cores.

Once you have cut your insulation twist the cable cores together, this will give you a neat and easy to terminate the cable.

Now that you have prepared the cable it is time to look at the plug.

Preparing the plug

First, start by removing the screw that holds the plug together. This will allow you access to the terminations and the fuse holder within the plug.

Inside the plug you will see three different markings next to the terminations, they are:

L = Live = This is where the brown cable is terminated

N = Neutral = This is where the blue cable is terminated

E = Earth = This is where the yellow and green cable is terminated

You will also see a fuse holder – ensure that you have the correct fuse fitted for the appliance that you are using. The majority of standard plugs will come fitted with a 13A fuse.

Some cables feature a cable clamp – this is to clamp the cable in place and to reduce the risk of the terminations being pulled out if the cable is pulled. If your plug has one of these you will need to remove it before wiring.

Terminating the cable

Now that you have prepared the cable and the plug you are ready to start terminating the connections.

Each terminal will have a screw located on top. Loosen the screw using a screwdriver so that you can fit the twisted end of the core into each terminal.

Remember:

L = Live = This is where the brown cable is terminated

N = Neutral = This is where the blue cable is terminated

E = Earth = This is where the yellow and green cable is terminated

Terminate all connections into the correct terminals and secure them all in place using your screwdriver.

If your plug has a cable clamp it is now time to fit that back in place.

Before fitting the plug’s cover ensure that there are no exposed wires from the bottom of the plug and that all cables are terminated and sitting nicely within the body of the plug.

And that’s all there is to it! You have now successfully wired a plug and it should be ready to plug into a socket. Always take care when performing any electrical work and consult an electrician if needed.

What should i do if my cable only has two wires?

Some electrical equipment and appliances only use two cable cores within their plugs. These types of devices are called “double insulated” appliances and do not use the earthing wire for protection.

As you can see from the image above, the live and neutral cables are still terminated in the same locations. These can also be identified as L or N normally marked on the body of the plug.

You should follow the exact same steps as above (just without using the earth wire). Always ensure that the screw for the earth terminal is tight so it does not come out.

So there you have it – a step-by-step guide on how to wire a 3-wire and 2-wire plug. If you follow these instructions carefully, you should be able to do it without any problems. And if you do run into any issues, don’t hesitate to get in touch with us for help. Thanks for reading!

Can I use a UK plug in the United States or Canada?

Without an adaptor, you cannot use a UK plug in the United States or Canada. They use plugs called Type A and Type B plugs. If you are interested in learning more about them or how to wire them check out or article here.